Product Comparison · Furniture Refinishing
Furniture Repair and Refinishing Kit: The Tools and Supplies You Need (2026)
The four pieces of a furniture repair and refinishing kit, from their Amazon listings and the makers' pages: a DEWALT 20V MAX drill and impact driver kit, the DEWALT DWE6423 random orbit sander, the REALINN 28-piece filler and marker kit, and Howard Restor-A-Finish, matched to the damage each fixes.
What Tools and Supplies Do You Need in a Furniture Repair and Refinishing Kit?
Four things cover most furniture repairs: a cordless drill and impact driver pair for loose joints, stripped screws and new hardware, a random orbit sander for leveling and taking an old finish back to wood, a filler-and-marker kit for scratches, chips and holes, and a finish restorer for pieces whose finish is tired but intact. The pairing below is a DEWALT 20V MAX drill and impact driver kit, a DEWALT DWE6423 random orbit sander, the REALINN 28-piece wood repair kit and Howard Restor-A-Finish, each described from its Amazon listing and, where one was read, its maker's page. Add sandpaper in a grit sequence, 0000 steel wool and clean cotton rags, and the kit is complete.
Updated October 2026.
We did not test these products ourselves; this guide is built from Amazon's product listings.
A note on sources
The four Amazon listings are the base of this guide; DEWALT's pages for the DCK240C2 kit and the DWE6423 sander and Howard Products' page for Restor-A-Finish were also read and are named where they add a fact. No manufacturer page for REALINN was available to read, so everything stated about the repair kit comes from its listing. Where a source is silent, the table says "not stated".
Match the tool to the damage
Loose joints, wobbly legs, stripped screw holes, new hinges or drawer slides. A drill/driver drills pilot holes and drives screws; an impact driver drives long screws and lag bolts without the bit slipping. On old furniture most of this work is low-torque and in awkward spots, so compactness matters more than headline power.
A finish that is worn through, flaking or too far gone to blend. That is a sanding job. A 5-inch random orbit sander takes flat tops back to bare wood and levels filler; spindles and carvings are still hand work. Our sandpaper grit sequence for refinishing furniture covers which grits to buy and in what order.
Scratches, chips, gouges, nail holes and discolored patches. Fillers rebuild the missing wood, markers color the scratch or redraw the grain, and a scraper levels the repair. Our guide to fixing scratches without refinishing covers how far that approach stretches before a sander is the honest answer.
A finish that is dull, faded, water-ringed or lightly scratched, but still there. Neither sanding nor filling is the first move there; a finish restorer blends the blemish into the existing finish. Our Howard Restor-A-Finish review covers what it fixes and what it cannot.
The four pieces of the kit
DEWALT 20V MAX Drill and Impact Driver Kit (DCK240C2)
Per the listing, the kit includes 2 batteries, a charger and a bag, the drill's high-performance motor delivers up to 300 UWO, and the impact driver delivers up to 1,400 in-lbs of torque. The listing says both tools have integrated LED work lights with a 20-second delay and a compact design for tight areas, and the impact driver's 1/4 in. hex chuck accepts 1 in. bit tips for one-handed loading.
DEWALT's page names the two tools: the DCD771 20V MAX 1/2-in drill/driver, with a two speed transmission (0-450 / 0-1500 RPM), 300 unit watts out and a 1/2-in single sleeve ratcheting chuck, and the DCF885 1/4-in impact driver, compact at 5.55-in front to back and 2.8 lbs, with a 3 LED light ring and a 20 second delay. DEWALT lists the batteries as two 20V MAX Li-ion 1.3Ah packs with a 20V MAX charger and a contractor bag, and gives a 3 Year Limited Warranty, 1 Year Free Service and a 90 Days Satisfaction Guarantee.
Check the current price on Amazon
DEWALT DWE6423 5-Inch Random Orbit Sander
Per the listing, the DWE6423 is a corded, variable speed, 5-inch random orbit sander whose 3-Amp motor spins the pad at 8,000 - 12,000 OPM. The listing says a separate counterweight design reduces vibration, a dust-sealed switch protects against dust ingestion, the dust port fits directly to the DWV010 or DWV012 dust collectors, and, for other vacuum systems with 1-1/4 in. hoses, the DWV9000 Universal Quick Connector. Per the listing, the shorter height lets the user get closer to the workpiece, rubber overmold improves grip, and the dust bag locks one-handed.
DEWALT's page repeats those bullets, describes a hook-and-loop pad, lists the motor as brushed, includes one dust bag with the sander, and gives the same 3 Year Limited Warranty, 1 Year Free Service and 90 Days Satisfaction Guarantee. Neither source states the weight, orbit diameter or cord length.
Check the current price on Amazon
REALINN Wood Furniture Repair Kit (Set of 28)
Per the listing, the Set of 28 includes 12 touch up fillers, 8 touch up markers, 1 wood putty, 1 beewax, 2 brushes, 2 sandpaper, 1 sponge and 1 scraper. Per the listing, it restores scratches, chips, cracks, holes and discoloration on wooden floors, doors and furniture such as desks, chairs, beds, wardrobes, bookcases and cabinets. The listing says to apply the filler into the cracks, then smooth the surface with the scraper, and that the markers touch up superficial scratches or draw wood grain.
Per the listing, the fillers come in 12 colors (White, Black, Light Gray, White Maple, Yellow Maple, Deep Pine, Earthy Yellow, Yellow Teak, Red Cherry, Cedar, Dalbergia, Walnut) and the markers in 8 (White, Gray, Oak, Maple, Cherry, Walnut, Mahogany, Black), and the tip is to add the lighter repair filler first, then gradually add the darker wood repair filler until you achieve the desired shade. No manufacturer page was available for REALINN, so the listing is the only source, and it states no filler chemistry, dry time or sandability.
Check the current price on Amazon
Howard Restor-A-Finish
Per the listing, Restor-A-Finish is a finish-penetrating formula that restores wood finishes while blending out minor scratches, blemishes and abrasions, without removing any of the existing finish. The listing says it removes white heat rings and water marks, sun fade, oxidation and smoke damage with a simple wipe-on, wipe-off process, and is available in nine colors: Neutral, Maple-Pine, Golden Oak, Cherry, Walnut, Mahogany, Dark Walnut, Dark Oak and Ebony Brown. The container on the listing is 16 fl oz.
Howard Products' page says to apply with a small pad of cloth, a small area at a time, and immediately wipe dry, never pouring it directly on the finish; it also names a pad of super fine 0000 steel wool, rubbed lightly in the direction of the wood grain. The page says to wait at least 30 minutes and then apply a coat of Howard Feed-N-Wax, and to wait 30 days before putting polyurethane or another clear coat over it. Its limits are stated plainly: not recommended for floors or exterior surfaces, it may not penetrate harder "plastic" finishes, and it may not work well on "one step stain and poly" finishes. The page carries a DANGER flammability caution, calls for adequate ventilation, lists hydrogenated mineral oil, isopropanol and acetone as contents, and warns that it may stain fabric, carpet or linoleum.
Check the current price on Amazon
Side-by-side
| Job | DEWALT DCK240C2 kit | DEWALT DWE6423 sander | REALINN Set of 28 | Howard Restor-A-Finish |
|---|---|---|---|---|
| Sources read | Listing + DEWALT page | Listing + DEWALT page | Listing | Listing + Howard Products page |
| What it is | DCD771 1/2-in drill/driver + DCF885 1/4-in impact driver, 2 × 1.3Ah batteries, charger, bag (DEWALT) | Corded 5-inch variable speed random orbit sander (listing) | 12 fillers, 8 markers, putty, beewax, 2 brushes, 2 sandpaper, sponge, scraper (listing) | Finish-penetrating restorer, nine colors, 16 fl oz (listing) |
| Headline figure | 300 UWO drill; up to 1,400 in-lbs impact torque (listing) | 3-Amp, 8,000 - 12,000 OPM (listing) | 28 pieces, 12 filler and 8 marker colors (listing) | Wipe-on, wipe-off (listing) |
| Loose joints and hardware | Yes | No | No | No |
| Stripping and leveling | No | Yes, flat surfaces | No | No |
| Scratches, chips, holes | No | Levels filler | Yes (listing) | Minor scratches and blemishes only (listing) |
| White rings, fade, oxidation | No | Only by removing the finish | No | Yes (listing) |
| Dust control | Not stated | Bag; port fits DWV010/DWV012, DWV9000 adapter for 1-1/4 in. hoses (listing) | Not applicable | Not applicable |
| Warranty | 3 Year Limited, 1 Year Free Service, 90 Days (DEWALT) | 3 Year Limited, 1 Year Free Service, 90 Days (DEWALT) | Not stated | Not stated on the listing |
Best for
| If the job is… | Pick |
|---|---|
| Re-screwing joints, swapping hinges and slides | DEWALT 20V MAX drill and impact driver kit |
| Taking a tabletop back to bare wood before a new finish | DEWALT DWE6423 random orbit sander |
| A gouge, chip or nail hole in a piece you will not refinish | REALINN Set of 28 |
| A scratch you want to hide rather than fill | REALINN Set of 28 (markers) |
| A white ring or faded top on a finish that is otherwise sound | Howard Restor-A-Finish |
Which to buy first
If you only buy one thing, buy the sander. The DWE6423's listing names variable speed and a dust port that fits the DWV010 or DWV012 dust collectors, and DEWALT's page adds a hook-and-loop pad and an included dust bag.
Buy the drill and impact driver kit when the problem is structural. Wobbly chairs, drawers off their slides and tabletops pulled away from their aprons are driver jobs, and the DCK240C2 pairs a two-speed drill with a compact impact driver and two batteries, per DEWALT's page. If your pieces are all cosmetic, skip it.
Buy the REALINN kit for cosmetic damage you can see from across the room. Twelve filler colors and eight marker colors are on its listing, and the listing's mixing tip is for reaching the shade you want.
Buy Howard Restor-A-Finish before you sand anything. If the finish is intact and the damage is rings, fade or light scratches, its listing says a wipe-on, wipe-off pass restores the finish without removing it.
FAQ
What tools and supplies do you need in a furniture repair and refinishing kit?
A cordless drill and impact driver for joints and hardware, a 5-inch random orbit sander for stripping and leveling, a filler-and-marker kit for scratches, chips and holes, and a finish restorer for tired but intact finishes, plus sandpaper in a grit sequence, 0000 steel wool and cotton rags. The four picks here are the DEWALT DCK240C2 kit, the DEWALT DWE6423, the REALINN Set of 28 and Howard Restor-A-Finish.
Do you need both a drill and an impact driver?
For furniture, the drill does most of it: pilot holes and driving screws into old wood. The impact driver earns its place on long screws and lag bolts into legs and rails. The DCK240C2 listing gives the drill up to 300 UWO and the impact driver up to 1,400 in-lbs of torque.
Can Howard Restor-A-Finish replace sanding?
Only when the finish is still there. Per its listing it restores the finish without removing any of the existing finish and blends out minor scratches; Howard's page says it is not for floors or exterior surfaces and may not work on harder "plastic" or "one step stain and poly" finishes. A finish that is worn through needs the sander.
Sources
- DEWALT — product page "20V MAX* 1.3 Ah Drill Driver/Impact Driver Combo Kit" (DCK240C2) on dewalt.com, read October 2026.
- DEWALT — product page "5-in Variable-speed Random Orbit Sander" (DWE6423) on dewalt.com, read October 2026.
- Howard Products — product page "Restor-A-Finish - Wood Finish Restorer" on shop.howardproducts.com, read October 2026.
- Amazon product listings for the DEWALT 20V MAX Drill and Impact Driver (DCK240C2), the DEWALT Random Orbit Sander, Variable Speed, 5-Inch (DWE6423), the REALINN Wood Furniture Repair Kit - Set of 28, and Howard Restor-A-Finish, 16 Fl oz: title, brand and feature bullets.
No spam. Unsubscribe anytime.
Affiliate Disclosure



